Increasing the efficiency of the furnace depending on the operating conditions of the furnaces. Part 2. The technology of joint loading of lumpy anthracite and fluxed local specs
Loading...
Date
2024-06-26
Journal Title
Journal ISSN
Volume Title
Publisher
Scientific and practical journal "Economics and technical engineering"
Abstract
The article analyzes the reasons for the growing research interest in the technology of loading lump anthracite of different fractions into a blast furnace to increase its efficiency. It is shown that loading blast furnaces with additional lump anthracite can be an effective way to improve the technical and economic indicators of their operation, especially on furnaces that work without the technology of pulverized fuel injection. It was noted that the traditional directions of development of iron smelting technology in blast furnaces practically mastered. At the same time, the problem of improving the quality of iron ore raw materials has not yet been fully resolved. A conclusion was made about the need for a new type of iron ore raw material, which would combine the best properties of agglomerate and pellets and would not have their negative features. A number of technologies for the production of a new type of iron ore raw material have been developed - fluxed local specs from iron ore concentrates of various degrees of enrichment, with an increased iron content compared to agglomerate and pellets and with an increased residual carbon content. A comparison of technological parameters of production and metallurgical characteristics of agglomerate, pellets and the developed unfluxed mono-raw material was made. If two technologies are combined: loading of lump anthracite into the blast furnace for partial replacement of coke and mono-raw material, namely, local specs with a high content of iron and residual carbon, then analytical estimates show that, for example, when loading into furnace No. 9 with useful volume of 5000 m3 up to 70 kg/t of lump anthracite, blowing up to 60 m3/t of natural gas and using local specs with a residual carbon of 2.85 % and an iron content of 70.45 %, it is possible to reduce coke consumption to 322.68 kg/t of cast iron and increase furnace productivity to 12733 t/day, which can be compared with the best indicators achieved in the world when blowing PCI, but without large capital costs.
У статті проаналізовані причини зростання дослідницького інтересу щодо технології завантаження кускового антрациту різної фракції в доменну піч для підвищення ефективності її роботи. Показано, що завантаження доменних печей додатковим кусковим антрацитом може бути ефективним способом покращення техніко-економічних показників їх роботи, особливо на печах, які працюють без технології вдування пиловугільного палива. Відзначено, що традиційні напрямки розвитку технології виплавки чавуну у доменних печах практично освоєно. При цьому проблема підвищення якості залізорудної сировини повною мірою поки що не вирішена. Виконаний порівняльний аналіз традиційних видів залізорудної сировини. Розроблено низку технологій виробництва нового виду залізорудної сировини – офлюсованих локальних спеків із залізорудних концентратів різного ступеня збагачення, з підвищеним, порівняно з агломератом та окатишами, вмістом заліза та залишкового вуглецю. Виконано порівняння технологічних параметрів виробництва та металургійних характеристик агломерату, окатишів і розробленої офлюсованої моносировини. Якщо поєднати дві технології: завантажити в доменну піч кускового антрациту для часткової заміни коксу та моносировини – локальних спеків із підвищеним вмістом заліза та залишкового вуглецю, то аналітичні оцінки показують, що, наприклад, при завантаженні у піч №9 корисним об’ємом 5000 м3 до 70 кг/т шматкового антрациту, вдуванні до 60 м3/т природного газу та використанні локальних спеків з залишковим вуглецем 2,85 % та вмістом заліза 70,45 % можливе скорочення витрати коксу до 322,68 кг/т чавуну та збільшення продуктивності печі до 12733 т/добу, це можна порівняти з кращими показниками, досягнутими у світі при вдуванні ПВП, але без великих капітальних витрат.
Description
Keywords
pulverized coal, anthracite, sinter, pellets, fluxed local specs, coke consumption, пиловугільне паливо, антрацит, агломерат, окатиші, офлюсовані локальні спеки, витрата коксу
Citation
Chuprynov, Y., Kassim, D., Shmeltser, K., Lykhova, I., & Renkas, O. (2024). Increasing the efficiency of the furnace depending on the operating conditions of the furnaces. Part 2. The technology of joint loading of lumpy anthracite and fluxed local specs. Scientific and practical journal "Economics and technical engineering". Vol. 2 No. 1 (2024), 107–118.